Connect coal storage, dewatering, and cleat flow to gas production.
All explanations and solutions are visible in this reading view. Use the interactive models to test your understanding. Reading time varies; the minute labels describe the class plan.
Coalbed methane
00–02 min · 2 min
Coalbed methane
Coal can generate methane, store it on internal surfaces, and transmit it through natural fractures. This lecture follows gas from its storage site to a producing well. We will explain why some wells first produce water, calculate gas inventories, and evaluate what can prevent stored methane from becoming useful production.
Conceptual teaching diagram · not to scale
Study explanation
Coalbed methane is often abbreviated CBM; coal seam gas is another term used in some regions. Its engineering behavior differs from a simple free-gas sandstone because adsorption and water-bearing fracture flow can be important together. All numerical examples in this lecture are fictional. Gas volumes are standard volumes at 101.325 kPa absolute and 288.15 K unless explicitly described otherwise.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 07S1001 / 24
Learning plan
02–04 min · 2 min
Your route through this lecture
By the end, you should be able to connect matrix storage, cleat flow, pressure reduction, and water handling. We will refresh adsorption, build a dewatering explanation, calculate initial and releasable inventory, then test the explanation against a fictional production profile. The final questions include complete solutions for independent study.
Study explanation
The 90-minute plan includes deliberate calculation and discussion time. Read each definition before using its equation. During a worked example, distinguish three answers: how much gas initially exists, how much could leave adsorption sites at equilibrium, and how much actually reaches the well. The first two can be estimated with the supplied data; the last requires flow and operating information.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0702 / 24
Prerequisite refresher
04–07 min · 3 min
Refresh: storage and deliverability
Storage describes how much methane a rock can contain. Deliverability describes how readily methane can reach a well at a useful rate. Porosity measures pore-volume fraction; permeability describes transmission through connected paths. An inventory calculation therefore cannot, by itself, predict the production rate of a coal seam.
Conceptual teaching diagram · not to scale
Study explanation
Picture a container with a large capacity but a narrow outlet. Its size and outlet conductance answer different questions. Coal adds another complication: much of its gas may be held at surfaces and must first desorb. A large gas inventory can coexist with low production if matrix transfer is slow, cleats are disconnected, or water strongly restricts gas flow.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0703 / 24
Coalbed methane
07–10 min · 3 min
Coal can be both source and reservoir
Coal originates from accumulated organic material altered during burial. Methane can form through thermal processes or microbial activity, depending on geological history. Coal may retain that methane and act as its reservoir. A seam description must therefore consider both the history that supplied gas and the present conditions that retain and transmit it.
Conceptual teaching diagram · not to scale
Study explanation
Thermogenic and microbial describe gas-generation pathways, not automatically the production quality of a seam. Present gas content also depends on retention, leakage, pressure history, moisture, and the properties of the coal. Do not assume that every coal seam contains the same gas quantity or that all seams in one basin behave identically. Regional geological evidence is necessary for a real assessment.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 07S1004 / 24
Coalbed methane
10–14 min · 4 min
The matrix stores; cleats connect
The matrix is the coal material between fractures. It provides extensive internal surface area for adsorption. Cleats are natural fractures that can form connected pathways through the seam. Productive behavior depends on matrix-to-cleat transfer as well as cleat spacing, connection, orientation, stress, and water saturation.
Conceptual teaching diagram · not to scale
Study explanation
The distinction is a useful conceptual model rather than a claim that all coal has identical block geometry. Some gas can occupy free pore or fracture space as well. Even if a matrix block releases gas, an unconnected cleat may not carry that gas to the well. Measurements of gas content and measurements of permeability therefore complement each other.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0705 / 24
Coalbed methane
14–18 min · 4 min
Adsorption is gas held at surfaces
In adsorption, methane molecules accumulate at solid surfaces. Free gas occupies available pore or fracture volume as a gas phase. Desorption is the release of previously adsorbed molecules. For coal, substantial gas can be associated with adsorption, so a free-gas pore-volume calculation may omit an important part of the initial inventory.
Conceptual teaching diagram · not to scale
Study explanation
Adsorption should not be confused with absorption into a bulk material. In this course the adsorbed content is reported as standard cubic metres of gas per metric tonne of coal on a stated dry basis. Laboratory measurements may use other moisture and ash bases or report excess rather than absolute adsorption. Always check the report before multiplying content by a seam mass.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0706 / 24
Coalbed methane
18–22 min · 4 min
An equilibrium curve relates content to pressure
At a fixed temperature, the simple Langmuir model estimates equilibrium adsorbed content. Here C is gas content in standard m³/t, VL is limiting content in the same units, p is absolute pressure, and PL is the pressure at half limiting content. Use the same pressure units for p and PL.
\[C(p)=V_L\frac{p}{P_L+p}\]
Study explanation
The model approaches VL as pressure becomes large; it does not reach that limiting content at every reservoir pressure. At p = PL, substitution gives C = VL/2. Parameters depend on the sample and test conditions. An isotherm is an equilibrium storage relationship at constant temperature and contains no time variable, so it cannot directly give a production rate.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 07S0607 / 24
Coalbed methane
22–25 min · 3 min
Coal may initially be undersaturated
A coal sample can contain less methane than its isotherm capacity at initial reservoir pressure. It is then undersaturated relative to that isotherm. Reducing pressure does not immediately require all stored gas to desorb. Important equilibrium desorption may begin only when the declining capacity matches the actual gas content.
Conceptual teaching diagram · not to scale
Study explanation
Suppose the actual content is 6 standard m³/t, while the isotherm capacity at initial pressure is 8. The coal does not contain the missing 2 standard m³/t simply because capacity exists. Pressure must fall until capacity reaches 6 before further reduction requires equilibrium release in this simplified model. Transport and temperature changes can make an actual field response more complicated.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0708 / 24
Coalbed methane
25–29 min · 4 min
Why remove water from a gas reservoir?
Dewatering means producing water from a water-bearing coal seam to reduce pressure. A pressure reduction can make desorption possible. As water saturation decreases, gas may also gain better-connected flow paths through cleats. These effects can allow gas rate to increase after a period of water-dominated production.
Conceptual teaching diagram · not to scale
Study explanation
Water production is therefore part of a coupled reservoir process, not simply an unwanted liquid stream. It still requires pumping, handling, analysis, and an appropriate destination. The relationship between pumping and reservoir pressure depends on connectivity and water influx. A lower water level at a well does not prove that every part of the seam has reached the pressure needed for desorption.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0709 / 24
Coalbed methane
29–33 min · 4 min
Follow gas from the surface site to the well
The conceptual sequence is pressure reduction, desorption at matrix surfaces, transfer through the matrix, gas movement through connected cleats, and flow into the well. Every step matters. If transfer is slow or a cleat is disconnected, methane released locally may remain unavailable to the producing well during the planned project period.
Conceptual teaching diagram · not to scale
Study explanation
Use this sequence as a diagnostic map. A low gas rate could result from insufficient pressure reduction, low initial gas content, slow matrix transfer, poor cleat permeability, water blockage, or unfavorable well conditions. A gas-content measurement answers only part of that map. Pressure, water, gas-rate, and well-condition observations are needed to narrow the explanation.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0710 / 24
Coalbed methane
33–37 min · 4 min
Gas relative permeability can improve
When gas and water share cleat space, each phase has an effective permeability. Gas relative permeability krg compares gas effective permeability with a reference absolute permeability k. As water distribution changes, gas pathways may improve even without changing the reference k. The simplified relation is kg = k × krg.
Conceptual teaching diagram · not to scale
Study explanation
Relative permeability is a property of a fluid–rock system at specified conditions and saturation, not a universal constant for all coal. If k = 0.10 mD and krg increases from 0.05 to 0.20, effective gas permeability increases from 0.005 to 0.020 mD in this comparison. Actual k may also change with stress and matrix shrinkage, so the two effects must be distinguished.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0711 / 24
Coalbed methane
37–40 min · 3 min
A possible production sequence
Some CBM wells begin with relatively high water rate and low gas rate. As pressure and saturation evolve, gas rate may rise, reach a peak, and later decline. This sequence is a teaching pattern, not a required shape for every coal seam. Dry seams and different pressure, gas-content, and connectivity histories can behave differently.
Conceptual teaching diagram · not to scale
Study explanation
A rising gas rate does not imply that gas is being created by pumping. Methane already stored in the reservoir is becoming more available to the well. Rate may later decline as connected inventory depletes or flow conditions worsen. To interpret an observed profile, also check pump settings, pressure measurements, downtime, and changes in well equipment.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0712 / 24
Interpretation activity
40–44 min · 4 min
Read a fictional water and gas profile
In this teaching dataset, water rate falls from 200 to 30 m³/day between days 0 and 180. Gas rate rises from 1,000 standard m³/day to 20,000 at day 90, then falls to 15,000 at day 180. Identify the gas peak and propose one reservoir explanation and one operating explanation.
Conceptual teaching diagram · not to scale
Study explanation
The peak is the largest observed gas rate, at day 90. A reservoir explanation is that initial pressure reduction and improved gas relative permeability enable a buildup, followed by depletion or conductivity loss. An operating explanation could involve changed pumping or well restrictions. The five observations alone cannot distinguish these explanations. They are synthetic values, not a fitted field forecast.
Worked solution
Observed peak: day 90, 20,000 standard m³/day. A plausible reservoir sequence is dewatering, desorption, improved gas movement, and later depletion. Confirm with pressure and saturation-related evidence. Compare pump settings and well-condition records to test an operating explanation. Do not infer a universal CBM curve from this example.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0713 / 24
Coalbed methane
44–48 min · 4 min
Depletion can close cleats
Effective compressive stress describes how strongly the rock framework is compressed in a specified model. If pore pressure falls while total stress stays fixed, effective compression rises. Cleats may narrow and their permeability may decrease. Pressure reduction can therefore help release methane while simultaneously making some flow pathways less conductive.
Conceptual teaching diagram · not to scale
Study explanation
The introductory relation is effective stress = total stress − α × pore pressure, where α is the Biot coefficient. A value of one is a specified approximation rather than a rule for every rock. Real depletion can also change total stresses. This lesson explains the direction of a possible effect; it does not supply a universal permeability-versus-pressure law.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0714 / 24
Coalbed methane
48–51 min · 3 min
Desorption can also shrink the matrix
As adsorbed gas leaves, coal matrix shrinkage can tend to widen surrounding cleats. This competes with stress-related closure. The net permeability change depends on coal properties, stress path, pressure, and connection geometry. It cannot be assumed to increase or decrease in the same way for all reservoirs.
Conceptual teaching diagram · not to scale
Study explanation
Keep the competing mechanisms separate when explaining a result. One changes how strongly the cleat surfaces are compressed; another changes matrix dimensions as adsorption changes. A field or laboratory permeability trend is needed to determine which effect dominates over a particular pressure interval. This is one reason that maximizing early pumping rate is not automatically the best development strategy.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0715 / 24
Coalbed methane
51–55 min · 4 min
Measure the gas content carefully
Sampling can release methane before the coal is sealed. A gas-content assessment may account for lost gas, gas collected during laboratory desorption, and gas remaining as a residual. Gas can be underestimated if an important component is ignored. Sampling method, timing, moisture, and ash corrections must accompany the reported number.
Conceptual teaching diagram · not to scale
Study explanation
Lost gas is not measured in exactly the same manner as gas collected from a sealed sample; it may require estimation. Treat resulting uncertainty honestly. For inventory calculations, the coal mass and gas content must refer to the same material basis. A dry, ash-free content cannot be multiplied directly by a wet, ash-bearing mass and expected to give a consistent result.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0716 / 24
Worked example
55–59 min · 4 min
Calculate an initial adsorbed inventory
For a matching dry coal mass M, multiply mass in metric tonnes by gas content C in standard m³/t. The product is a standard gas volume. Our worked interval contains 2 million tonnes with initial measured content of 6 standard m³/t. Calculate its initial adsorbed inventory before considering later pressure conditions.
\[G_{\mathrm{ads},i}=M C_i\]
Study explanation
The gas content here is supplied as an actual measured initial adsorbed content on the same dry basis as the mass. It is not simply the capacity at an arbitrary pressure. Multiplying 2,000,000 t by 6 standard m³/t cancels tonnes and gives 12,000,000 standard m³. This calculation does not include an independently estimated free-gas contribution.
Worked solution
Gads,i = 2,000,000 t × 6 standard m³/t = 12 million standard m³. This is an initial adsorbed inventory on the supplied mass and gas-volume basis. No production time has been calculated.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0717 / 24
Worked example
59–62 min · 3 min
Calculate an equilibrium decrease
In the same worked interval, let equilibrium content at a later pressure be 3 standard m³/t. The initial-to-later content difference is 3 standard m³/t. Multiplying this difference by the matching dry mass gives the inventory that could leave adsorption sites as equilibrium changes between these specified states.
\[\Delta G_{\mathrm{ads,eq}}=M(C_i-C_f)\]
Study explanation
The initial inventory was 12 million standard m³. The later equilibrium adsorbed inventory is 2 million t × 3 standard m³/t = 6 million standard m³. Their difference is 6 million. Some released gas may remain as free gas, take too long to move, or be left when the well becomes uneconomic. Therefore equilibrium decrease should not be labeled produced or recovered gas.
Worked solution
ΔGads,eq = 2,000,000 × (6 − 3) = 6 million standard m³. The final adsorbed inventory is also 6 million standard m³. Actual recovery requires a flow, operating, and abandonment assessment.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0718 / 24
Independent practice
62–68 min · 6 min
W07.1: try the inventory calculation
A coal interval contains 3 × 106 metric tonnes of dry coal. Initial gas content is 7 standard m³/t and final equilibrium content is 4 standard m³/t, both on the matching basis. Calculate initial adsorbed inventory and the equilibrium decrease. Write one sentence explaining the physical meaning of each answer.
Study explanation
Work through units before numbers. Initial inventory uses initial content, whereas equilibrium decrease uses the difference between initial and final content. Students sometimes multiply the final content by mass and mistakenly report that remaining quantity as the amount released. Check your answer by adding final remaining inventory and the equilibrium decrease; the result should equal the initial inventory.
Worked solution
Initial adsorbed inventory = 3 × 10⁶ × 7 = 21 million standard m³.
Final equilibrium inventory = 3 × 10⁶ × 4 = 12 million standard m³.
Equilibrium decrease = 3 × 10⁶ × (7 − 4) = 9 million standard m³.
The 9 million is an equilibrium storage change, not a guaranteed production volume.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0719 / 24
Explain the mechanism
68–73 min · 5 min
W07.2: explain the delayed gas response
Why might a water-bearing CBM well have a low initial gas rate but an increasing gas rate later? Identify one reason this improvement might fail to occur. Develop a sequence that connects water production, pressure, adsorption, matrix transfer, and cleat gas flow instead of listing those terms without a causal connection.
Study explanation
A complete explanation should state which process changes which condition. Producing water can reduce pressure; sufficient pressure reduction can enable desorption. Lower water saturation may improve gas relative permeability. Gas then still needs connected cleats. An initially undersaturated seam may require further drawdown before desorption, while poor connectivity or stress closure can suppress delivery even if gas is released.
Worked solution
Dewatering can lower seam pressure until desorption becomes important. As cleat water saturation falls, gas relative permeability may increase, allowing more methane to reach the well. The buildup may fail if cleats are poorly connected, matrix transfer is slow, gas content is low, coal remains undersaturated, or depletion closes the main cleats.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0720 / 24
Apply your understanding
73–78 min · 5 min
Check the claim about faster pumping
A proposed plan states: “The fastest possible dewatering will always maximize gas production.” Evaluate this claim using the mechanisms from this lecture. Consider pressure reduction, cleat permeability, matrix transfer, and the ability to handle produced water. A useful answer identifies what must be measured before selecting a pumping strategy.
Which statement is supported by the CBM model?
Study explanation
Pressure reduction is useful only within a connected system that can deliver gas and handle water. A rapid local pressure change may not propagate evenly through the seam and may increase effective compression of cleats. Production strategy should be supported by pressure, gas and water rates, stress-dependent permeability, and well-condition information rather than a universal fastest-pumping rule.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0721 / 24
Appraisal checklist
78–82 min · 4 min
What data would you request?
To appraise a CBM seam, combine gas-content and adsorption measurements with pressure observations, core properties under relevant stress, cleat description, water behavior, and a well test. Ask how each measurement reduces uncertainty. A long list becomes useful only when the connection to a development decision is clear.
Conceptual teaching diagram · not to scale
Study explanation
Gas content constrains storage; an isotherm helps describe equilibrium pressure response. Cleat and stress-dependent permeability evidence informs deliverability. Pressure and gas/water histories test the proposed dewatering explanation. Water composition and available treatment/disposal options inform feasibility and cost. None of these measurements alone establishes commercial reserves, but together they can support a defined appraisal program.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0722 / 24
Lecture review
82–85 min · 3 min
A complete explanation of CBM
A coal seam can retain methane by adsorption in its matrix. Connected cleats provide important flow paths. Water removal may reduce pressure enough for desorption and improve gas movement, while stress and shrinkage can change permeability in competing ways. Inventory, equilibrium release, and recovered production must be reported as distinct quantities.
Conceptual teaching diagram · not to scale
Study explanation
Check whether you can reconstruct this explanation without reading the slide. Use a labeled sketch with a matrix block, adsorption sites, a water/gas-bearing cleat, and a well. Add arrows indicating desorption, matrix transfer, and flow. If you can explain why a large inventory can still yield a low rate, you have connected storage and deliverability rather than memorized definitions.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0723 / 24
Exit ticket
85–90 min · 5 min
Exit check and next lecture
Before finishing, calculate what half the initial gas content would mean for the same coal mass, then explain why halving content does not prove that rate halves. Next lecture, we connect the reservoir to a well: placement, casing, cement, fracture stages, effective stress, and maintaining a conductive pathway throughout depletion.
Study explanation
For fixed mass, initial adsorbed inventory is directly proportional to initial gas content. Rate has additional dependencies: transfer behavior, pressure, connectivity, saturation, and well conditions. Revisit W07.1 and W07.2 until both arithmetic and explanation are clear. All essential ideas and solutions are contained in this lecture; linked references provide optional background rather than missing course content.
UNCONVENTIONAL GAS RESERVOIR / LECTURE 0724 / 24
COMPLETE CHAPTER TEXT
Lecture 07: chapter notes
The original student knowledge-base chapter is reproduced below as a continuous reference, alongside the expanded explanations above.
Learning targets
Explain the roles of coal matrix and cleats.
Describe why many CBM wells initially produce substantial water.
Distinguish equilibrium gas release from recoverable production.
Core knowledge
Coal can be both the source and the reservoir for methane. The coal matrix contains adsorption sites; natural fractures called cleats commonly provide important flow paths. Cleat spacing, connection, stress, and water saturation influence deliverability.
Many water-bearing coal seams require dewatering to reduce pressure. Pressure reduction can enable desorption and improve gas relative permeability as water saturation falls. A possible production sequence is early water-dominated production, increasing gas rate, a gas peak, and eventual decline. This is a conceptual pattern, not a profile every coal seam must follow. Background reading: Pennsylvania Geological Survey: Methane from coal.
Initial measured gas content may lie below the isotherm capacity at initial pressure. Such coal is undersaturated with respect to that isotherm. Desorption may become important only after pressure reaches the value at which equilibrium capacity matches actual gas content.
Permeability also changes during depletion. Increasing effective stress can close cleats, while desorption-related matrix shrinkage can tend to open them. The net result is reservoir dependent. Rapid water removal is therefore not automatically the best production strategy.
Gas-content sampling also needs care: gas can be lost before a sample is sealed, some gas desorbs during testing, and some remains as residual gas. The reported moisture and ash basis must match any mass used for gas-in-place calculations.
Worked example
A coal interval has a matching dry coal mass of \(2\times10^6\) t and measured initial gas content of 6 standard m³/t:
If equilibrium content at a later pressure is 3 standard m³/t, the modeled equilibrium decrease is 6 million standard m³. Transport, water, abandonment pressure, and economics determine how much actually reaches the surface.
Practice
W07.1: A matching dry coal mass is \(3\times10^6\) t. Initial gas content is 7 standard m³/t and final equilibrium content is 4 standard m³/t. Calculate initial adsorbed inventory and the equilibrium decrease.
W07.2: Why might a water-bearing CBM well have low initial gas rate but increasing gas rate later? Identify one reason this improvement might fail to occur.
Takeaway: CBM development links adsorption, pressure reduction, water handling, and cleat flow.