LECTURE 05 / 90-MINUTE LEARNING PLAN

Tight gas reservoirs

Explain how pore networks, fluids, and stress control gas transmission through tight rock.

All explanations and solutions are visible in this reading view. Use the interactive models to test your understanding. Reading time varies; the minute labels describe the class plan.

Lecture 05 · 90 minutes

00–02 min · 2 min

Tight gas: why connected pores can supply gas slowly

Tight gas reservoirs contain gas in rock that transmits it poorly. This lecture connects pore throats, cementation, water saturation, and stress to delivery. You will use a simplified Darcy model to compare flow cases and distinguish absolute permeability from the effective permeability available to gas when water is also present.

Conceptual teaching diagram · not to scale

Study explanation

The aim is to reason about restrictive flow without pretending that one simple expression predicts every gas well. Begin with rock texture, then add the influence of fluids and pressure. Calculations use relative changes and effective gas permeability. Every time the incompressible Darcy expression is used, keep its assumptions visible so a proportional comparison is not mistaken for a standard-condition gas-well forecast.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0501 / 26

Learning route

02–04 min · 2 min

Build the flow model one factor at a time

First identify the host rock and pore-network restrictions. Then define absolute, effective, and relative permeability. Introduce pressure gradient, viscosity, flow area, and path length through Darcy’s law. Finish with controlled comparisons, measurement limitations, and a diagnosis of why a gas-bearing interval might still deliver poorly.

Study explanation

By the end, you should calculate effective gas permeability using kg=k krg and compute ratios in a steady incompressible linear-flow model. You should also explain why actual gas flow needs additional treatment of density changes, geometry, and operating conditions. A final practical skill is evaluating whether a laboratory measurement represents the stress, fluid state, orientation, and scale relevant to an in-situ problem.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0502 / 26

Prerequisite refresher

04–07 min · 3 min

Refresh capacity, occupancy, and movement

Porosity measures pore fraction, saturation identifies the fluids occupying those pores, and permeability describes transmission through connected pathways. These are related physically but are not interchangeable measurements. A rock may contain gas-filled pores while the connected paths used by gas are narrow, water-restricted, or poorly connected to the well.

Conceptual teaching diagram · not to scale

Study explanation

Use the storage calculation to identify how much pore space is occupied by gas, then ask a different question about how that gas can move. The connection between two pore bodies can control flow more strongly than either body’s storage capacity. Water can alter which connections are available to gas even when bulk porosity remains unchanged. This distinction is central to tight gas and remains important in shale and coal.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0503 / 26

Concept

07–10 min · 3 min

Tight gas commonly occurs in sandstone or carbonate

Tight gas is commonly associated with low-permeability sandstone and carbonate reservoirs. The gas may have migrated from another source into these rocks. Their pore systems can hold free gas but restrict delivery. Classification therefore combines geology with a flow challenge; it is not a complete description of reservoir history, storage, or commercial potential.

Conceptual teaching diagram · not to scale

Study explanation

A sandstone framework or carbonate pore system can become tight through several geological processes. Some low-permeability rocks also contain natural fractures that change large-scale flow. The word tight should therefore motivate measurement of the actual connected system. A historical threshold can help compare descriptions, but development feasibility depends on pressure, geometry, stimulation, fluid behavior, costs, and the degree to which stored gas can reach a well.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 05S0704 / 26

Concept

10–13 min · 3 min

A permeability boundary is only a screening convention

A permeability around 0.1 mD is often encountered as a historical tight-gas screening boundary. It is not a universal physical divide or economic cutoff. An unstimulated rate, a stimulation opportunity, and a commercial project depend on more than one permeability value, and definitions have varied with technical and institutional context.

Conceptual teaching diagram · not to scale

Study explanation

A property changes continuously rather than becoming fundamentally different at exactly 0.1 mD. A reservoir slightly above that value may still be difficult to develop, while one below it may have useful fractures or an effective completion. When using a threshold, state its purpose and source. Do not convert a classification rule into a prediction that every rock on one side is profitable or that every rock on the other side is unproductive.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 05S2105 / 26

Concept

13–16 min · 3 min

Compaction and cementation can restrict pore space

Compaction changes the grain framework during burial, while mineral cement can occupy pore space and narrow connections. Both can reduce transmission through the rock. The distribution of the remaining pore throats matters: a rock can retain storage bodies but still have a very restrictive connected network for moving gas.

Conceptual teaching diagram · not to scale

Study explanation

Rock texture and geological alteration influence both pore volume and connectivity. Their effects are not captured by porosity alone. Cement concentrated at critical throats may have a large influence on permeability even if some larger pores remain. Conversely, dissolution or fractures can create different flow routes. The appropriate interpretation comes from geological description together with representative measurements rather than a single texture label.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 05S0806 / 26

Concept

16–19 min · 3 min

Pore throats govern connections between storage spaces

A pore body provides local space; a pore throat connects that space to neighboring pores. Narrow throats and long, tortuous paths can strongly restrict flow. Two rocks with equal pore-volume fractions can therefore have different permeability. Connected pathways all the way to a larger fracture or well are essential for useful delivery.

Conceptual teaching diagram · not to scale

Study explanation

A local open pore contributes to storage even if the route leaving it is narrow or disconnected. Flow through a network depends on its bottlenecks and path structure. This is why a diagram of isolated circles cannot explain production without also showing their connections. In a tight reservoir, characterizing pore-throat restrictions and how they respond to fluids and stress is often as important as measuring total pore volume.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0507 / 26

Concept

19–22 min · 3 min

Absolute permeability describes a reference flow condition

Absolute permeability, k, is the reference rock permeability measured with a single fluid phase under stated conditions. It is commonly expressed in mD for description. Its value can depend on the rock’s stress state and measurement setup. The same reference permeability should be used when defining relative permeability for a phase system.

Conceptual teaching diagram · not to scale

Study explanation

State the fluid, pressure, stress, sample orientation, and method when reporting a permeability measurement. In idealized comparisons, k is treated as a fixed rock property. In real reservoirs, stress evolution and damage can change the connected pore system, while gas measurements can require particular interpretation. The definition is still useful because it provides the denominator for describing how coexistence of other phases restricts the mobility available to gas.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 05S0308 / 26

Concept

22–25 min · 3 min

Effective permeability identifies the flow available to gas

When gas and water coexist, the permeability available to gas is its effective permeability kg. Water can occupy paths that would otherwise transmit gas. Effective gas permeability is therefore different from the absolute single-phase reference k. The phase distribution and connection geometry matter as well as the total amount of gas in the pores.

Conceptual teaching diagram · not to scale

Study explanation

A high gas saturation does not necessarily mean every important pathway is gas-filled. Distribution at constrictions can affect mobility strongly. Effective permeability describes the resulting ability of a selected phase to transmit flow through the multiphase system. It should not be confused with effective porosity: one concerns transmission and the other a stated pore-volume definition. Always specify the phase when reporting an effective permeability.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0509 / 26

Concept

25–28 min · 3 min

Relative permeability is a ratio, not another pore fraction

Gas relative permeability krg is effective gas permeability divided by the reference absolute permeability. In the simplified model, multiply k by krg to obtain kg. Relative permeability is dimensionless and reflects the fluid system and saturation state. It is not equal to gas saturation by definition.

\[k_g=k\,k_{rg}\]
Conceptual teaching diagram · not to scale

Study explanation

If gas occupies 70% of pore volume, its relative permeability is not automatically 0.70. Connectivity, wettability, pore geometry, and saturation history can affect the relationship. Curves must be measured or modeled appropriately. The teaching exercises provide krg directly, so the arithmetic remains simple. The physical interpretation is that coexistence with another phase commonly reduces the transmission available to a selected phase.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0510 / 26

Worked permeability calculation

28–32 min · 4 min

A small reference permeability can become smaller for gas

For k = 0.02 mD and krg = 0.10, effective gas permeability is 0.002 mD. Only one-tenth of the reference permeability is available to gas under this simplified phase condition. The calculation illustrates why water effects can matter greatly in a rock whose absolute permeability is already low.

Conceptual teaching diagram · not to scale

Study explanation

The result is obtained by multiplying 0.02 by the dimensionless factor 0.10, leaving mD. It does not say that only 10% of the gas is recoverable or that gas saturation is 10%. These are distinct quantities. If water saturation or phase connectivity changes, krg can change even while the assumed reference k remains fixed in a controlled comparison.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0511 / 26

Concept

32–35 min · 3 min

Pressure gradient supplies the driving force

Pressure-driven flow depends on a pressure difference over a path length. A larger inlet-to-outlet pressure difference can increase modeled flow if other factors stay fixed. The gradient is the pressure drop divided by distance. High reservoir pressure alone does not establish a rate without a connected pathway and an outlet pressure.

Conceptual teaching diagram · not to scale

Study explanation

In a simple straight flow path, use Δp/L rather than pressure alone. Two systems at different absolute pressures could have the same pressure difference, while different fluid properties may still change their rates. Actual gas density varies with pressure, so a simple incompressible comparison has limits. The driving-force idea remains useful when discussing why a completion must connect gas-bearing rock to a lower-pressure producing well.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0512 / 26

Concept

35–38 min · 3 min

Viscosity resists movement through the pathway

Dynamic viscosity μ describes a fluid’s resistance to deformation and flow. In the simplified Darcy model, rate decreases when viscosity increases while permeability, geometry, and pressure gradient remain fixed. Viscosity belongs to the fluid description; permeability belongs to the rock-flow system under its stated reference conditions.

Conceptual teaching diagram · not to scale

Study explanation

Keep rock properties and fluid properties separate even though both appear in a rate relationship. A unit conversion also matters: the SI form uses μ in Pa·s and k in m². For controlled ratios, matching units can cancel, but an absolute calculation requires consistency. This course emphasizes proportional comparisons so you can explain physical trends without turning a simplified expression into an unsupported gas-well forecast.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0513 / 26

Concept

38–41 min · 3 min

Linear Darcy flow combines the controls

For steady, one-dimensional, single-phase incompressible flow, q equals permeability k times flow cross-sectional area Af times pressure drop Δp, divided by viscosity μ and path length L. In SI, q is m³/s. The expression describes a defined flow geometry and is used here mainly for proportional comparisons.

\[q=\frac{kA_f}{\mu}\frac{\Delta p}{L}\]
Conceptual teaching diagram · not to scale

Study explanation

Steady means the modeled flow state is not changing with time. One-dimensional means the simplified flow follows one principal direction through a known cross-section. Single phase means only one fluid phase transmits the modeled flow, and incompressible means its density is treated as constant. These conditions differ from many real gas-well situations. List the assumptions before applying the equation and identify which are being used only as an educational simplification.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0514 / 26

Concept

41–44 min · 3 min

Flow area is not mapped drainage area

Af is the cross-sectional area perpendicular to the modeled flow direction. It is not automatically the reservoir map area A used in gas volumetrics. The path length L also depends on geometry. Changing a vertical well to a horizontal well changes the flow problem and cannot be represented by one arbitrary area substitution.

Conceptual teaching diagram · not to scale

Study explanation

In a rectangular laboratory sample, the cross-section and length are straightforward. In a reservoir, flow may converge toward a well or approach fractures through a different geometry. Volumetric area describes how much rock is included in an inventory, while flow area describes where fluid crosses in a rate model. Using one symbol without defining its geometry can accidentally mix two different physical calculations.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0515 / 26

Worked comparison

44–50 min · 6 min

Worked comparison: lower permeability, higher pressure drop

In the simplified Darcy model, permeability falls from 0.02 to 0.005 mD while pressure difference doubles. Keep flow area, viscosity, and path length fixed. Calculate the ratio q₂/q₁ and interpret whether the greater driving force fully compensates for the smaller permeability. This is a comparison, not an absolute gas rate.

\[\frac{q_2}{q_1}=\frac{0.005}{0.02}\times2=0.50\]
Conceptual teaching diagram · not to scale

Study explanation

The permeability ratio is 0.005/0.02=0.25. The pressure-drop ratio is 2. Their product is 0.50 because all other factors cancel. Thus the modeled second rate is half the first rate. This is useful physical reasoning, but an actual gas problem would also need density/compressibility treatment, the appropriate geometry, and phase-flow information. The example does not calculate a standard m³/day rate.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0516 / 26

Concept

50–53 min · 3 min

Why real gas needs an additional treatment

Gas density changes along a pressure gradient. A quantitative gas-well calculation must account for compressibility, an appropriate flow geometry, and often gas–water relative permeability. Very small pores or high velocities can introduce additional effects. The simple incompressible expression is therefore a teaching comparison, not a complete unconventional-gas production model.

Conceptual teaching diagram · not to scale

Study explanation

Gas properties such as Z and viscosity can vary with pressure, and flow near a well differs from a straight constant-area sample. At high velocities, additional pressure losses can matter; at very small scales, the flow description may need further corrections. You are not expected to derive these advanced models here. The required skill is recognizing why the assumptions of a simple model need to be checked before numerical prediction.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0517 / 26

Concept

53–56 min · 3 min

Stress and water can reduce in-situ mobility

A dry, unstressed specimen can transmit gas differently from water-bearing rock under reservoir stress. Stress can narrow pores and fractures; water can reduce gas relative permeability. A useful measurement program reproduces relevant conditions as closely as possible and records the remaining differences between laboratory behavior and the reservoir.

Conceptual teaching diagram · not to scale

Study explanation

Two distinct changes can occur. The reference pore network itself may become less transmissive under greater compression, changing k. Separately, coexistence with water can restrict the gas pathways, changing krg. These effects should not be blended into an unexplained single correction factor. Later lectures introduce effective stress and show why depletion can change fracture or cleat conductivity as production continues.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0518 / 26

Explore · 8 minutes

56–64 min · 8 min

Explore one flow control at a time

Use the Darcy comparison explorer to change permeability, pressure difference, flow area, viscosity, or path length. Predict the rate multiplier before adjusting a control. Keep the simplified steady incompressible linear-flow assumptions visible. Explain which of those assumptions would need reassessment before applying the trend to a real gas well.

Study explanation

Doubling k, Af, or Δp doubles the modeled rate if the other factors remain fixed. Doubling μ or L halves it. Combining changes multiplies their individual ratios. The activity separates mathematical sensitivity from a full engineering prediction. A real intervention may change several coupled properties at once, and a well’s geometry and pressure field cannot be reduced to a chosen multiplier without a justified model.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0519 / 26

Concept

64–67 min · 3 min

Choose a representative permeability test

When requesting core-flow data, specify stress, fluid composition, saturation, sample orientation, temperature where relevant, and measurement method. Consider whether fractures are preserved and whether the sample represents the target layers. A precise laboratory number can be unsuitable for a reservoir decision if it describes a very different physical condition.

Conceptual teaching diagram · not to scale

Study explanation

Useful reporting includes the source depth, bedding direction, confining and pore pressures, preparation method, and fluid system. Comparing measurements under several relevant conditions can show sensitivity rather than hiding it. A short sample still cannot establish reservoir-scale continuity by itself. Combine laboratory evidence with logs, geological correlation, pressure tests, and production observations according to the decision being made.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 05S0820 / 26

Practice W05.1

67–73 min · 6 min

W05.1: find effective gas permeability

A rock has absolute permeability k = 0.04 mD and gas relative permeability krg = 0.15. Calculate effective gas permeability. Then repeat with krg = 0.05, holding k fixed. State the change as a ratio and explain what physical quantity the dimensionless factor describes.

Conceptual teaching diagram · not to scale

Study explanation

The first effective permeability is 0.04×0.15=0.006 mD. The second is 0.04×0.05=0.002 mD, or one-third of the first value. This controlled example changes the relative transmission available to gas while leaving the reference permeability unchanged. A different saturation or phase distribution can produce such a change. It does not imply the gas inventory is reduced to one-third.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0521 / 26

Practice W05.2

73–76 min · 3 min

W05.2: change area and path length

In the simplified Darcy comparison, flow cross-sectional area doubles and flow length halves, with every other factor fixed. Find the rate multiplier. Then explain why the result cannot directly predict the benefit of a real horizontal gas well. Your answer should identify at least one geometry or gas-flow issue.

Conceptual teaching diagram · not to scale

Study explanation

Rate is proportional to Af/L, so the multiplier is 2/(1/2)=4. A horizontal well changes the spatial pressure field, connected contact, and possible fracture geometry. Multiphase and compressible behavior also matter. The comparison teaches proportionality within a specified model, but it does not establish that an actual horizontal well will produce exactly four times the rate of a particular vertical well.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0522 / 26

Applied diagnosis

76–79 min · 3 min

Diagnose a tight-gas delivery problem

A fictional well has meaningful gas-filled pore volume but a low rate. Its dry-core permeability appears adequate for the initial screening model. Suggest three explanations that remain possible and identify a measurement or observation to investigate each. Keep gas quantity, in-situ mobility, and well connection as separate parts of your diagnosis.

Conceptual teaching diagram · not to scale

Study explanation

The dry core may overstate permeability under reservoir stress; water may lower gas relative permeability; and damage or a weak completion may restrict access to connected rock. Other possibilities include an unrepresentative sample or insufficient pressure difference. Good diagnosis does not choose a mechanism merely because it is familiar. It links each hypothesis to evidence that could support or challenge it.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0523 / 26

Self-check

79–84 min · 5 min

Check the meaning of relative permeability

A rock has k = 0.10 mD, Sg = 0.70, and a measured krg = 0.20 for the stated condition. Which value should be used to calculate effective gas permeability? Explain why the gas saturation number cannot simply replace the measured relative permeability, even though both are dimensionless.

What is effective gas permeability for the supplied condition?

Study explanation

Use krg=0.20, giving effective permeability 0.02 mD. Gas saturation describes volume occupancy, whereas relative permeability describes transmission compared with a reference condition. The two can be related through a measured or modeled curve, but they are not identical by definition. Dimensionless quantities are not automatically interchangeable. Their physical meaning and reference basis must also match the equation.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0524 / 26

Concept

84–87 min · 3 min

Increasing drawdown does not repair every restriction

Drawdown is the pressure difference between reservoir supply and the producing well at the stated location. A larger driving force can help flow, but it does not create missing connections automatically. Stress change, water behavior, damage, and conductivity can also respond. A useful intervention addresses the diagnosed limitation rather than assuming pressure alone controls rate.

Conceptual teaching diagram · not to scale

Study explanation

In the controlled Darcy comparison, increasing pressure difference increases rate with all other factors fixed. Real reservoirs need not hold all those factors fixed. Lower pore pressure may increase effective compression or alter fluid behavior. The purpose of this qualification is to preserve the correct model scope. Use measured pressure and flow evidence to evaluate whether a proposed change improves the controlling link in the production chain.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0525 / 26

Review and exit check

87–90 min · 3 min

Review the controls and the assumptions

Explain why pore throats, cementation, water, and stress matter in tight gas. Distinguish k, kg, and krg. State the assumptions of linear Darcy flow and reproduce the two ratio examples. Finally, describe the information missing before a laboratory measurement or proportional comparison can predict a standard gas-well production rate.

Conceptual teaching diagram · not to scale

Study explanation

You should now be able to describe a flow restriction without confusing it with low gas storage. The next lecture applies the same reasoning to shale, where storage sites, layering, mechanics, and stimulation vary together. Keep the common production chain in mind: gas must move through the matrix, enter connected conductive pathways, and reach a well under appropriate pressure and operating conditions.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0526 / 26

COMPLETE CHAPTER TEXT

Lecture 05: chapter notes

The original student knowledge-base chapter is reproduced below as a continuous reference, alongside the expanded explanations above.

Learning targets

Core knowledge

Tight gas commonly occurs in low-permeability sandstone or carbonate. Compaction, cementation, small pore throats, and poor connectivity can restrict flow even where gas-filled pores are present. A permeability around 0.1 mD is sometimes used as a historical screening boundary; it is not a universal physical or economic cutoff. The Government of British Columbia's tight gas overview discusses this boundary. EIA discusses the changing meaning of the classification in Where our natural gas comes from.

For steady, one-dimensional, single-phase incompressible flow:

\[ q=\frac{kA_f}{\mu}\frac{p_{\mathrm{in}}-p_{\mathrm{out}}}{L} \]

\(A_f\) is flow cross-sectional area, \(L\) is flow length, and \(\mu\) is dynamic viscosity. This form is used here to reason about proportional changes. Its volume rate is at the fluid's flowing conditions; it is not automatically a standard gas rate.

Real gas density changes along a pressure gradient. Quantitative gas-well calculations require compressibility treatment, appropriate geometry, and often relative permeability. At very low pore sizes or high velocities, additional flow effects may matter.

When gas and water coexist:

\[ k_g=k\,k_{rg} \]

\(k_g\) is effective gas permeability and \(k_{rg}\) is gas relative permeability. For \(k=0.02\) mD and \(k_{rg}=0.10\), \(k_g=0.002\) mD. Water occupying important pore throats can strongly restrict gas movement.

Core tests should represent relevant stress, fluid, orientation, and sample condition. A dry, unstressed measurement can differ substantially from gas mobility in the reservoir. SLB: Defining and determining permeability provides further background.

Worked comparison

In the simplified Darcy model, reduce permeability from 0.02 to 0.005 mD while doubling pressure difference, with all other factors fixed:

\[ \frac{q_2}{q_1}=\frac{0.005}{0.02}\times2=0.50 \]

The modeled rate is halved. A larger pressure difference has not fully compensated for lower permeability.

Practice

Takeaway: Gas-filled pore volume alone cannot predict tight gas deliverability.

Next: lecture 06 →Open the course reference

LECTURE 05 · 90 MINUTES

Lecture contents

  1. 01Tight gas: why connected pores can supply gas slowly2 min
  2. 02Build the flow model one factor at a time2 min
  3. 03Refresh capacity, occupancy, and movement3 min
  4. 04Tight gas commonly occurs in sandstone or carbonate3 min
  5. 05A permeability boundary is only a screening convention3 min
  6. 06Compaction and cementation can restrict pore space3 min
  7. 07Pore throats govern connections between storage spaces3 min
  8. 08Absolute permeability describes a reference flow condition3 min
  9. 09Effective permeability identifies the flow available to gas3 min
  10. 10Relative permeability is a ratio, not another pore fraction3 min
  11. 11A small reference permeability can become smaller for gas4 min
  12. 12Pressure gradient supplies the driving force3 min
  13. 13Viscosity resists movement through the pathway3 min
  14. 14Linear Darcy flow combines the controls3 min
  15. 15Flow area is not mapped drainage area3 min
  16. 16Worked comparison: lower permeability, higher pressure drop6 min
  17. 17Why real gas needs an additional treatment3 min
  18. 18Stress and water can reduce in-situ mobility3 min
  19. 19Explore one flow control at a time8 min
  20. 20Choose a representative permeability test3 min
  21. 21W05.1: find effective gas permeability6 min
  22. 22W05.2: change area and path length3 min
  23. 23Diagnose a tight-gas delivery problem3 min
  24. 24Check the meaning of relative permeability5 min
  25. 25Increasing drawdown does not repair every restriction3 min
  26. 26Review the controls and the assumptions3 min
Course project and solutions ↗

Study explanation