LECTURE 01 / 90-MINUTE LEARNING PLAN

The unconventional gas problem

Connect the gas stored in a rock to the pathways that deliver it to a well.

All explanations and solutions are visible in this reading view. Use the interactive models to test your understanding. Reading time varies; the minute labels describe the class plan.

Lecture 01 · 90 minutes

00–02 min · 2 min

Gas in the rock, gas at the well

This lecture introduces unconventional gas reservoirs by following one question: how can rock contain a useful amount of gas yet deliver very little to a well? You will connect the gas molecule, the host rock, storage space, and flow pathways before making your first reservoir-volume calculations.

Conceptual teaching diagram · not to scale

Study explanation

Natural gas is stored underground under pressure. An engineer must estimate both how much gas is present and how it could move into a well. Those questions require different evidence. During this 90-minute lecture, read each physical explanation, use the diagrams, and complete the calculation pauses. All numerical rock examples are fictional teaching data. The reading view contains the explanations and worked solutions needed to study without a lecturer.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0101 / 26

Learning route

02–04 min · 2 min

A route from description to calculation

First, classify tight gas, shale gas, coalbed methane, and gas hydrates. Then define porosity, permeability, and saturation. Finally, calculate gas-filled pore volume and explain what the answer represents. By the end, you should be able to separate a claim about storage from a claim about production.

Study explanation

The sequence matters because a formula becomes useful only after its quantities are physically clear. Porosity tells us the fraction of rock occupied by pores; saturation tells us what fills those pores; permeability concerns movement through connected pathways. We will use simple gas–water systems first. Later lectures add gas expansion, adsorption, stress effects, and economics. For now, the strongest result is a correct volume calculation accompanied by its assumptions.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0102 / 26

Prerequisite refresher

04–07 min · 3 min

Start with fractions and dimensions

A percentage must become a fraction before multiplication: 8% is 0.08. A bulk volume includes both solid material and pores. A pore volume includes only the spaces inside the rock. Keep area in m², thickness in m, and volume in m³ when using SI calculations.

Conceptual teaching diagram · not to scale

Study explanation

Suppose 8 out of every 100 equal units of rock volume are pore space. The porosity fraction is 8/100, or 0.08. This fraction has no units because both numerator and denominator are volumes in the same units. Multiplying a dimensionless fraction by a bulk volume gives a pore volume. Confusing a percentage with a fraction creates a factor-of-100 error, so write the conversion explicitly before substituting numbers.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0103 / 26

Concept

07–10 min · 3 min

What natural gas means

Natural gas is a mixture dominated by methane, CH₄. Composition varies between reservoirs and can include other hydrocarbons and nonhydrocarbon components. The term unconventional concerns the storage and production setting. Methane from a shale reservoir is the same chemical molecule as methane from a conventional reservoir.

Conceptual teaching diagram · not to scale

Study explanation

A reservoir label does not fully specify the fluid. Composition affects properties, processing needs, and behavior as pressure and temperature change. This course begins with simplified dry-gas examples, but the physical distinction remains useful: identify the fluid separately from its geological container. When comparing two reservoirs, differences in production may reflect rock properties, pressure, completion, or composition. The word unconventional alone does not provide the missing measurements.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 01S0104 / 26

Concept

10–13 min · 3 min

Why a reservoir is called unconventional

Production may be difficult because the rock transmits gas poorly, much gas is adsorbed on surfaces, or gas is stored in solid hydrate. These settings can require particular well layouts, stimulation, pressure management, or dissociation. There is no single production difficulty shared in exactly the same way by every unconventional resource.

Conceptual teaching diagram · not to scale

Study explanation

Think of unconventional gas as a family of engineering problems. Very small pore connections can restrict pressure-driven movement in tight sandstone and shale. Adsorbed gas must leave surfaces and transfer through the matrix before it can reach a well. Hydrate-bound gas must be released from a solid phase. These mechanisms can coexist. Classification helps choose the next physical model; it does not replace investigation of a specific formation.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 01S0105 / 26

Concept

13–16 min · 3 min

A conventional petroleum-system comparison

In a familiar conventional setting, hydrocarbons form in a source rock, migrate into a separate reservoir, and accumulate beneath a seal. The producing reservoir may transmit gas relatively readily. This comparison helps explain why source, storage, and seal functions must be identified rather than assumed from the presence of a gas well.

Conceptual teaching diagram · not to scale

Study explanation

The comparison is a simplified geological model. Real petroleum systems vary, and unconventional reservoirs also need conditions that retain gas. A key difference in many shale systems is that generation and storage occur in the same interval, whereas a tight sandstone may receive gas from another source. We will revisit these relationships in Lecture 2. At this point, distinguish where gas originated from where it is currently stored and produced.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 01S0206 / 26

Concept

16–19 min · 3 min

Tight gas: small connections limit supply

Tight gas commonly occupies pores in low-permeability sandstone or carbonate. Gas can be present in considerable volume while narrow or poorly connected pore throats restrict movement. The principal first question is whether connected pathways can deliver gas from the matrix to the well at a useful rate.

Conceptual teaching diagram · not to scale

Study explanation

A pore body is a local storage space; a pore throat is a connection between spaces. Large pore bodies linked by restrictive throats can create a rock with appreciable porosity and poor permeability. Tight gas is commonly treated as free gas in pore space for an introductory inventory calculation. That storage description does not provide a rate. Core measurements, fluid saturations, pressure, and completion evidence are needed to assess delivery.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0107 / 26

Concept

19–22 min · 3 min

Shale gas: several storage sites

Shale gas occurs in gas-bearing shale or mudrock. Gas can occupy mineral pores, organic pores, and fractures, and can be adsorbed on surfaces. Their contributions differ between reservoirs. Very low matrix permeability and changing rock properties make characterization and a durable connection to the well important development questions.

Conceptual teaching diagram · not to scale

Study explanation

The matrix is the rock material surrounding the larger explicit fracture system. Organic material can contain tiny pores and adsorption surfaces, while the mineral framework also contributes storage and flow paths. A shale should not be modeled as an empty fractured box: gas must transfer from storage sites into connected pathways. Later lectures separate reservoir quality, meaning gas storage and supply, from completion quality, meaning the ability to create and maintain an effective connection.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 01S0908 / 26

Concept

22–25 min · 3 min

Coalbed methane: surfaces and cleats

Coalbed methane, often abbreviated CBM, occurs in coal seams. Adsorption commonly accounts for a substantial share of stored gas. Natural fractures called cleats provide important flow pathways. Many water-bearing coal seams need dewatering so pressure decreases and gas can desorb and flow through the cleat system.

Conceptual teaching diagram · not to scale

Study explanation

Adsorption means molecules accumulate at solid surfaces. Desorption is their release as conditions change. Dewatering means producing water from a water-bearing reservoir to help lower its pressure. These definitions already suggest why a coal well can produce water before its gas rate becomes substantial. Gas inventory, desorption, matrix transfer, and cleat flow must all be connected. Not every coal seam follows the same production sequence, so a generic profile is only a starting concept.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0109 / 26

Concept

25–28 min · 3 min

Hydrates: gas within a solid water lattice

Gas hydrates are crystalline solids in which water forms cages containing gas molecules, commonly methane. Their storage mechanism differs from free gas in pores and adsorption at surfaces. Producing hydrate-bound gas requires dissociation and then transport of gas and water through sediment, with heat supply and mechanical behavior also affecting performance.

Conceptual teaching diagram · not to scale

Study explanation

Dissociation is the breakdown of hydrate into gas and water. Suitable low-temperature, high-pressure conditions favor hydrate stability, but the exact boundary depends on composition and salinity. Hydrate should therefore be treated as a distinct stored phase. A large amount of methane contained in hydrate does not establish a recoverable project. Lecture 10 will explain why pressure reduction, cooling, multiphase flow, and sediment response must be considered together.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 01S1310 / 26

Compare the resources

28–32 min · 4 min

Classify by host, storage, and constraint

Use three connected descriptions for every resource: the host material, the main storage form, and the process limiting production. Tight sandstone emphasizes pore gas and restricted flow. Shale combines several storage sites and very low matrix permeability. Coal emphasizes adsorption and cleats. Hydrate sediment adds solid-phase dissociation and heat transfer.

Conceptual teaching diagram · not to scale

Study explanation

A correct classification should explain something about engineering behavior. Saying only “this is shale” is less useful than identifying shale pores and adsorption sites plus a need for connected conductive fractures. Classification is also a way to avoid applying the wrong inventory model. A free-gas pore-volume expression omits gas adsorbed on coal and gas bound in hydrate unless those inventories are modeled separately and consistently.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0111 / 26

Concept

32–35 min · 3 min

Porosity measures the space inside rock

Porosity, φ, is pore volume Vp divided by bulk volume Vb. It can be reported as a fraction or percentage. Bulk volume includes solid grains and pores together. Porosity describes storage space, but its value alone does not tell us whether that space is connected to a flowing well.

\[\phi=\frac{V_p}{V_b}\]
Conceptual teaching diagram · not to scale

Study explanation

Keep numerator and denominator on the same measurement basis. If a sample has 8 m³ of pores within 100 m³ of rock, its porosity is 0.08, or 8%. Total porosity includes all pores; definitions of effective porosity consider a useful subset and can vary by measurement method. We will examine that distinction in Lecture 2. In this first lecture, use the pore volume explicitly supplied by the problem.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0112 / 26

Concept

35–38 min · 3 min

Permeability concerns connected movement

Permeability, k, describes a rock’s ability to transmit fluid through its connected pore network. It is commonly described in millidarcies, microdarcies, or nanodarcies. Two samples with the same porosity may have different permeability because connection widths, path lengths, and fracture connectivity differ. Storage and flow therefore need separate evidence.

Conceptual teaching diagram · not to scale

Study explanation

Imagine two containers each holding the same amount of water. One drains through a wide connected outlet, while the other has only very narrow outlets. Their capacities can match while their discharge rates differ. Rock pore networks are more complicated, but the distinction helps. Permeability is a rock-flow property rather than a count of pores. Actual gas rate also depends on pressure difference, viscosity, geometry, and which other fluids occupy the pathways.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 01S0313 / 26

Concept

38–41 min · 3 min

Saturation identifies the pore occupants

Water saturation Sw is the fraction of the defined pore volume occupied by water. Gas saturation Sg is the fraction occupied by gas. In the simplified gas–water system used here, no oil or hydrate occupies that pore volume, so the two saturation fractions add to one.

\[S_g+S_w=1\]
Conceptual teaching diagram · not to scale

Study explanation

Saturation is referenced to pore volume rather than bulk rock volume. If 25% of the pores contain water, Sw is 0.25 and the remaining 75% contains gas in this two-phase example. The gas fraction of the whole rock is then porosity multiplied by gas saturation. If another phase is present, its saturation must be included and Sg=1−Sw alone is no longer sufficient.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0114 / 26

Concept

41–44 min · 3 min

Multiply the fractions in the correct order

Start with bulk rock volume. Multiply by porosity to obtain pore volume. Multiply the pore volume by gas saturation to obtain gas-filled pore volume. Each operation changes the physical quantity being described. The result still refers to the pressure and temperature in the reservoir unless a conversion is supplied.

\[V_{pg}=V_b\phi S_g\]
Conceptual teaching diagram · not to scale

Study explanation

The calculation can be written in one line, but reading it in stages helps catch mistakes. Vbφ represents all modeled pore space, including its water-filled part. VbφSg removes that water-filled part in a two-phase system. Do not subtract water saturation directly from porosity: these fractions have different denominators. For a uniform layer, bulk volume is mapped area multiplied by net thickness, provided units are consistent.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0115 / 26

Worked example

44–50 min · 6 min

Worked example: six reservoir cubic metres

A fictional rock block has bulk volume 100 m³, pore volume 8 m³, and water saturation 0.25. Find porosity, gas saturation, and gas-filled pore volume. Work through the three definitions before checking the solution. State whether the final gas volume is at reservoir conditions or standard conditions.

Conceptual teaching diagram · not to scale

Study explanation

First use the two supplied physical volumes rather than trying to infer a permeability. Porosity is 8/100=0.08, or 8%. Because only gas and water are modeled, gas saturation is 1−0.25=0.75. Multiplying 8 m³ of pore volume by 0.75 gives 6 reservoir m³ occupied by gas. No gas expansion or surface conversion has yet occurred. The calculation describes where gas is, rather than how much a well will recover.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0116 / 26

Concept

50–53 min · 3 min

Reservoir volume and reference volume

A cubic metre of gas in a high-pressure reservoir and a cubic metre at standard conditions generally contain different amounts of gas. Label the reference state whenever reporting gas volume. In this course, standard conditions are 101.325 kPa absolute and 288.15 K, with a standard-condition compressibility factor of one in exercises.

Conceptual teaching diagram · not to scale

Study explanation

The amount of gas remains the central physical quantity. Different reported volumes can describe the same amount at different pressure and temperature. A future lecture introduces Bg, the gas formation volume factor, to connect those volumes. For now, do not call the 6 reservoir m³ from the worked example “6 standard m³.” The label protects against an error that can be much larger than ordinary rounding differences.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0117 / 26

Units to keep nearby

53–56 min · 3 min

A compact SI unit check

One kilometre squared equals one million square metres. One megapascal equals one million pascals. One metric tonne equals 1,000 kilograms. For permeability, 1 mD equals 1,000 µD or one million nD. Convert a gauge pressure to absolute pressure before using a gas equation, and use kelvin for its temperature.

Study explanation

Area conversion deserves special care: 1 km is 1,000 m, so 1 km² is 1,000×1,000 m². A length conversion factor must be squared for an area. The gas equations later in the course require absolute pressure, referenced to vacuum, rather than gauge pressure, referenced to atmospheric pressure. Temperature in kelvin equals temperature in degrees Celsius plus 273.15. These are physical requirements of the equations rather than optional reporting preferences.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0118 / 26

Explore · 8 minutes

56–64 min · 8 min

Explore storage while holding flow unknown

Use the porosity explorer to change pore fraction and water saturation. Predict whether gas-filled pore volume should rise or fall before moving each control. Then explain why the explorer cannot supply a well production rate: it has no measurement of permeability, connected fracture geometry, operating pressure, or completion performance.

Study explanation

Changing porosity changes the available pore volume. Increasing water saturation leaves less modeled pore volume for gas. These responses follow directly from Vpg=Vbφ(1−Sw) for a gas–water system. Keep the distinction between a mathematical sensitivity and a geological prediction: a real change in porosity could also be associated with changes in permeability, but the explorer isolates the specified storage inputs. Write one sentence explaining each trend.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0119 / 26

Concept

64–67 min · 3 min

What a useful measurement should answer

A storage calculation needs volume, porosity, and fluid occupancy. A flow assessment needs information about connected permeability and pressure, and about the well’s connection to the rock. Ask what physical question a measurement addresses before treating a high number as favorable. One number rarely establishes the entire development case.

Conceptual teaching diagram · not to scale

Study explanation

A core sample might provide porosity and permeability, while logs extend observations along a well. A pressure measurement helps describe the force driving flow but does not establish how much connected rock is available. An engineer combines observations because the production chain has several links. In later lectures, we will add adsorption tests, gas properties, geomechanics, production history, and environmental information to the same evidence-based approach.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0120 / 26

Practice W01.1

67–73 min · 6 min

W01.1: calculate the gas-filled space

A fictional rock volume is 250 m³, its pore volume is 20 m³, and water saturation is 0.35. Calculate porosity, gas saturation, and gas-filled pore volume. Assume only gas and water occupy the modeled pores. Show a formula, numerical substitution, and units before opening the worked solution.

Conceptual teaching diagram · not to scale

Study explanation

Begin by deciding the denominator for each fraction. Porosity uses the entire bulk rock volume; saturation uses the pores. The water-filled pore volume is 20×0.35=7 m³, leaving 13 m³ for gas. Checking that the water and gas volumes sum to 20 m³ gives an independent verification. Because the problem supplies no reference-state conversion, report the gas-filled pore volume at reservoir conditions.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0121 / 26

Practice W01.2

73–76 min · 3 min

W01.2: equal porosity, different production

Two gas-bearing rocks each have 8% porosity. One produces readily and the other barely flows. Explain two possible reasons using physical mechanisms. Your explanation should connect a difference in the reservoir or well to a restriction on gas movement, rather than changing the given porosity value.

Conceptual teaching diagram · not to scale

Study explanation

Possible explanations include narrower or poorly connected throats, greater water occupancy of important flow pathways, disconnected fractures, stronger stress-related closure, or near-wellbore damage. Each mechanism can reduce gas delivery without requiring the two pore-volume fractions to differ. Pressure difference and gas viscosity can also change the observed rate. Distinguish a property of the rock from an operating condition when explaining your two selected reasons.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0122 / 26

Applied interpretation

76–79 min · 3 min

Diagnose a storage-only development claim

A fictional appraisal note states, “The rock has substantial gas-filled pore volume, so a high production rate is expected.” Identify the unsupported step. Then propose two measurements that would strengthen a delivery assessment. Describe what each measurement could show, and what uncertainty would remain after receiving it.

Conceptual teaching diagram · not to scale

Study explanation

The note jumps from an inventory-related observation to a rate prediction. Stress-representative permeability or relative-permeability testing could help establish matrix mobility. Pressure testing and completion diagnostics could help determine connected supply and well access. Measurements still have scale, method, and representativeness limits. A good response therefore replaces an unsupported confident statement with a qualified assessment and a plan to collect the missing evidence.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0123 / 26

Self-check

79–84 min · 5 min

Check the physical meaning

A gas–water rock has 10% porosity and 40% water saturation. Which fraction of the bulk rock volume is occupied by gas-filled pores? Choose an answer and explain the denominator of every fraction. This check combines porosity and saturation; it does not ask for a standard gas volume.

What fraction of bulk rock is gas-filled pore volume?

Study explanation

Porosity represents 0.10 of bulk rock volume. The gas fraction of the pore space is 1−0.40=0.60. Their product is 0.06 of bulk rock volume, or 6%. The 60% value describes only pores, while the 10% value includes water-filled and gas-filled pores together. Keeping those denominators explicit makes the multiplication physically understandable and prevents subtracting unrelated fractions.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0124 / 26

Concept

84–87 min · 3 min

Gas present is not gas recovered

Gas in place describes gas initially present within a defined reservoir volume. Recovered gas is the part produced under specified technical and operating conditions. Commercial reserves require further project evidence. Today’s pore-volume calculation supports an inventory description; it does not establish a production schedule, recovery factor, or commercial classification.

Conceptual teaching diagram · not to scale

Study explanation

These distinctions will remain important throughout the course. Gas can be present in isolated pores, remain strongly retained at abandonment conditions, move too slowly, or cost too much to produce. A well may also access only part of the mapped rock. Avoid attaching the word reserves to a simple storage result. A later integrated lecture connects inventory, deliverability, environmental requirements, costs, and project maturity.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0125 / 26

Review and exit check

87–90 min · 3 min

Explain the reservoir in one short paragraph

Finish by naming the host, storage mechanism, and principal delivery challenge for one resource. Then define porosity, permeability, and saturation in your own words. State how gas-filled pore volume is calculated and why its volume basis matters. If you can explain those links, you are ready to examine measurements and geology.

Conceptual teaching diagram · not to scale

Study explanation

A complete response should describe both the rock and the gas rather than listing labels. For tight sandstone, for example, free gas occupies pores but restricted connections can limit delivery. Porosity counts the pore fraction; saturation divides that pore volume among fluids; permeability concerns transmission. Gas-filled pore volume equals bulk volume multiplied by porosity and gas saturation. The result needs a reservoir-condition label until a valid gas-property conversion is applied.

UNCONVENTIONAL GAS RESERVOIR / LECTURE 0126 / 26

COMPLETE CHAPTER TEXT

Lecture 01: chapter notes

The original student knowledge-base chapter is reproduced below as a continuous reference, alongside the expanded explanations above.

Learning targets

Core knowledge

Natural gas is a mixture dominated by methane, with composition varying between reservoirs. “Unconventional” describes the reservoir and development challenge; it does not mean that the methane molecule is different. Low permeability, adsorption, or storage in a solid hydrate phase can require approaches beyond a simple unstimulated well. Read the introductory classification in EIA: Natural gas explained.

Resource Typical host Important storage Main production challenge
Tight gas Low-permeability sandstone or carbonate Mainly free gas in pores Restricted flow through narrow pore connections
Shale gas Gas-bearing shale or mudrock Free gas and adsorbed gas; proportions vary Very low matrix permeability and variable rock properties
Coalbed methane, CBM Coal seams Commonly substantial adsorption, plus free gas Desorption, cleat flow, and often water production
Gas hydrate Hydrate-bearing sediment Gas molecules within a solid water lattice Dissociation, heat supply, flow, and sediment response

Porosity measures space available within rock:

\[ \phi=\frac{V_p}{V_b} \]

Permeability describes the ability of a pore network to transmit fluid. Two rocks with the same porosity can have very different permeability because their pore throats and connections differ. A large storage volume does not guarantee a high production rate. See SLB: Permeability.

Saturation describes which fluids occupy the pore volume. For a gas–water system without oil or hydrate:

\[ S_g+S_w=1 \]

These quantities answer different questions: How much pore space exists? How is that space filled? How easily can the fluids move?

Worked example

A rock has bulk volume 100 m³, pore volume 8 m³, and water saturation 0.25.

The last answer is a reservoir-condition volume. It is not yet a standard gas volume.

Practice

Takeaway: Storage capacity and deliverability must be evaluated separately.

Next: lecture 02 →Open the course reference

LECTURE 01 · 90 MINUTES

Lecture contents

  1. 01Gas in the rock, gas at the well2 min
  2. 02A route from description to calculation2 min
  3. 03Start with fractions and dimensions3 min
  4. 04What natural gas means3 min
  5. 05Why a reservoir is called unconventional3 min
  6. 06A conventional petroleum-system comparison3 min
  7. 07Tight gas: small connections limit supply3 min
  8. 08Shale gas: several storage sites3 min
  9. 09Coalbed methane: surfaces and cleats3 min
  10. 10Hydrates: gas within a solid water lattice3 min
  11. 11Classify by host, storage, and constraint4 min
  12. 12Porosity measures the space inside rock3 min
  13. 13Permeability concerns connected movement3 min
  14. 14Saturation identifies the pore occupants3 min
  15. 15Multiply the fractions in the correct order3 min
  16. 16Worked example: six reservoir cubic metres6 min
  17. 17Reservoir volume and reference volume3 min
  18. 18A compact SI unit check3 min
  19. 19Explore storage while holding flow unknown8 min
  20. 20What a useful measurement should answer3 min
  21. 21W01.1: calculate the gas-filled space6 min
  22. 22W01.2: equal porosity, different production3 min
  23. 23Diagnose a storage-only development claim3 min
  24. 24Check the physical meaning5 min
  25. 25Gas present is not gas recovered3 min
  26. 26Explain the reservoir in one short paragraph3 min
Course project and solutions ↗

Study explanation